Say I have 3 multiparameters, each is a switch.
Is there a way to interlock these so that only one is active at a time.
Spencer
Interlocking Switches with Multiparameters
- KVRist
- Topic Starter
- 298 posts since 26 May, 2016 from Byron Bay, Australia
-
- KVRAF
- 10310 posts since 2 Sep, 2003 from Surrey, UK
I tried defining the "other 2" as targets of each one but that did not work -possibly because there essentially a feedback loop.
So I used a fourth MP (in Banks mode) to select them; drag through this and paste it into an MXXX A..H slot:
I have used MP11-13 as placeholder targets.
I guess you could put the target of the three switches into a bank in the fourth switch, then do away with the three switches.
So I used a fourth MP (in Banks mode) to select them; drag through this and paste it into an MXXX A..H slot:
Code: Select all
$eNq9Vltz2jgUfu+v0Hj3bZMgGwJmJtCxuaTshMJAWtJHxRZYg5AYWS6XX79HvhDjkrTN7FQvts7ROfq+c5F093G-4eg7VTGTomPZN9hCVAQyZGLVsRK9vHatj90Pd+Onp6eYag3iGP0FCy3Uk5yTbUzDGVtFekoE5R0LG7nQCnTgcyDIM6dhJlYyjiXsNJYh7VhOI-RrMtAlxeNhCwpPEC5XFuqrw4JqML25LSbeckkDHY-ENtH3hIkUxv2X0ZwdqQOTBq5ftRrNk2xA4gPIW2181WjD0gcm1imWh9l8y5nWVJllNiy5bVWlYFivNyw0JvuH4cTnMlgbMUgdEPpniCaJLkMaJ1yzKVFkQ8FZfApUuvfXItYtt9kAX927UwAM9cORKjTfSKkjQePY8McQgAUTodxlEfpEhACzqaJLxmEDyAnMJBMaDTlZxb4JBcDYm3zWsY2ddrt922xatdeWNarLahXnSgYARiqMTikFyyHjPP2ZR3IHLKX6SnhC41T2GLEgjXatZG+jdBnEFnuu47jDoYUmwFyxkKaa102dk6nruDb2fsO0-n7TRgmwM3Cdn5vWfkgntM8zESHO++ZiQc0ph0Ki4ZQnK1NF+AqbFKez2HhNPZhGPK+tbkWATe3nwPwhhmEQg2wQMi3z3vss1YbwrE3AbCZ3aWVmyvmO6SCy0GfQdKyJoABuS-PizZSPzKigMDEgT1OeVbb5y5xMqQqo0LHhUEBDw4TzGREr0ENfneTZRukU2XbJoaFdYVela5fo2n5r+CbdS-wed-LX+Nn-Dz-nTX52lZ9T4odxY+APf5dfpOifzWD9TYZOlWEd+USsezIRcNaDrZkZfzitPTQRLyI7TdeZyMkZpsJKWHoRDdbXz3JPYxRJxY7omXK5e6Xsjce4iFrWjVKdBU7T7QvMguJNs+Wcxc0-IGjVNRLg6Cx2g72e5Ufjr4SxFMXu314+3L7rXRpwXhdO3r+lc3HLl9HfTXfv33IkQL2VnOis1C5CqP8EQmlMvet3sy4-Syo44Fqvwb1+huNLf4MPn8g-x2MR-f5q6vaW9+w6-Hfy7RxHpd7rP0hiOMS9QLPvFO5YeFKh8qQovNKTAWiYqjY-8FSA8K2kOow03YzEUiIv0ZE5HGDRmDBufozcfBeLBXygBXuJUtDKeW2nTVne0+BRWzRLM+OAGi6Z-G5ZsFBH4+7dXCZwGqDyo6Bo72JJbVyQq5Xfit0P-wEp81A3
I guess you could put the target of the three switches into a bank in the fourth switch, then do away with the three switches.
- KVRist
- Topic Starter
- 298 posts since 26 May, 2016 from Byron Bay, Australia
I have a room problem. Its for the 3 Q buttons in DIPPER and the 3 Band Select in the GATE.
What I have works but you have to hit the new button twice. Once to deselect the old and once to engage the new.
The way I have done it is...
Q-N button settings
Set Q-M button to off
Set Q-W button to off
Set Dynamic Eq 1 - Eq 1 - Q1
But as I said you have to hit Q-N button twice.
There is some strange timing thing going on.
What I have works but you have to hit the new button twice. Once to deselect the old and once to engage the new.
The way I have done it is...
Q-N button settings
Set Q-M button to off
Set Q-W button to off
Set Dynamic Eq 1 - Eq 1 - Q1
But as I said you have to hit Q-N button twice.
There is some strange timing thing going on.
You do not have the required permissions to view the files attached to this post.