Connecting Vsti in Mulab with ORB Composer
-
- KVRist
- Topic Starter
- 203 posts since 26 Sep, 2014
If the module: midi channel splitter stands for 16 ports and 16 channels ?
-event output 1 = port 1 events ? ( 16 midi channels)
-event output 2= port 2 events ? ( 16 midi channels)
..and so on..
If this is the case then is this not userfriendly
Or makes this no sense ?
-event output 1 = port 1 events ? ( 16 midi channels)
-event output 2= port 2 events ? ( 16 midi channels)
..and so on..
If this is the case then is this not userfriendly
Or makes this no sense ?
- KVRAF
- 7137 posts since 8 Feb, 2003 from London, UK
Yes - that's what I'd already said earlier in the thread.
-
- KVRist
- Topic Starter
- 203 posts since 26 Sep, 2014
That's good news..cost me time to figure out.
Now i must try to get the transportation in ORB simoustanly working within MUlab for using MUdrum for instance.
How to set up this?
To all mUlab output must send a midiclock seems to me ..and where is the 'proxy' Patch Point module to find ?
Now i must try to get the transportation in ORB simoustanly working within MUlab for using MUdrum for instance.
How to set up this?
For detailed info on using MIDI channels, see the Composer doc page.Note that these MIDI Output modules can also be used as a target for sending MIDI clock. To set the MIDI clock output module, right-click the tempo display in the transport panel. If you want to send MIDI clock to multiple MIDI outputs then use a 'proxy' Patch Point module and connect it to all the MIDI outputs you want to send MIDI clock to.
To all mUlab output must send a midiclock seems to me ..and where is the 'proxy' Patch Point module to find ?
-
- KVRAF
- 1836 posts since 29 Mar, 2013
you will find the Patch Point module in "MODULES / OTHERS" Dont look for the word "Proxy" only "Patch Point"
Beauty is only skin deep,
Ugliness, however, goes right the way through
Ugliness, however, goes right the way through
-
- KVRist
- Topic Starter
- 203 posts since 26 Sep, 2014
Ah, thanks
I am puzzling now how to make this setup
I added the midi output clock module..
If i start Mulab transport it starts also the ORB composer transport, but i want start with ORB transport and that Mulab is following the transport. (intended use)
Should it not that ORB must send out a midi clock to MULAB ?..how to get this
I am puzzling now how to make this setup
I added the midi output clock module..
If i start Mulab transport it starts also the ORB composer transport, but i want start with ORB transport and that Mulab is following the transport. (intended use)
Should it not that ORB must send out a midi clock to MULAB ?..how to get this
- KVRAF
- 7137 posts since 8 Feb, 2003 from London, UK
I couldn't see that usage documented in the ORB manual - I might have missed it, though. Anyway, Mulab doesn't slave to external sync.
- KVRAF
- 7137 posts since 8 Feb, 2003 from London, UK
See viewtopic.php?f=79&t=357048 for that one.
- KVRAF
- 7137 posts since 8 Feb, 2003 from London, UK
- KVRAF
- 7137 posts since 8 Feb, 2003 from London, UK
Best to read up in general, then: https://modeaudio.com/magazine/5-tips-f ... tal-sounds